Health and Safety Policy

Our statement of intent, who is responsible for what, and how we keep people safe in the office and on client sites, including airports.

1. Purpose and scope

This policy sets out how Carefully Coded Ltd manages health and safety. It covers:

  • office and home working, which is most of our work
  • site work, including installing and commissioning equipment and software on client premises such as airports
  • everyone who could be affected by our work: our staff, subcontractors, client staff and members of the public.

We keep a written health and safety policy because our site work carries real risks and our clients need to see how we manage them.

This policy describes our general approach. For every site job we prepare separate, site-specific risk assessments and method statements (RAMS). These are available to clients on request.

2. Statement of intent

Carefully Coded Ltd will, so far as is reasonably practicable, protect the health, safety and welfare of our staff and of everyone affected by our work. We will meet our duties under the Health and Safety at Work etc. Act 1974 and the regulations made under it.

In particular, we will:

  • assess the risks of our work and put sensible controls in place before work starts
  • plan site work properly and agree it with the client before we arrive
  • make sure everyone doing the work is competent, trained and properly equipped
  • consult staff on health and safety matters
  • provide safe equipment and keep it maintained
  • report and learn from accidents and near misses
  • stop work if it becomes unsafe
  • review this policy every year.

Anyone working for us can stop a job they believe is unsafe, without blame.

Signed: Tom Emmerson, Director

Date: 19 November 2026

3. Organisation and responsibilities

Who Responsibilities
Tom Emmerson, Director Overall responsibility for health and safety. Approves all RAMS. Makes sure resources, training and equipment are in place. Investigates accidents. Reviews this policy
Everyone working for us Follow this policy, the RAMS and site rules. Take care of themselves and others. Use equipment and personal protective equipment (PPE) correctly. Report hazards, accidents and near misses straight away
Subcontractors Provide their own RAMS and evidence of competence. Follow our RAMS, this policy and site rules

Under the Management of Health and Safety at Work Regulations 1999, we must have access to competent health and safety advice. Our director, Tom Emmerson, acts as our competent person for health and safety. For higher-risk work, such as airside installations, work at height or electrical work, we obtain advice from a competent external specialist before work starts.

4. Arrangements

4.1 Risk assessment

We assess risks under the Management of Health and Safety at Work Regulations 1999. We have a general risk assessment for office and home working, which we review every year. We carry out a new assessment for every site job.

4.2 Risk assessments and method statements (RAMS)

Before any site work:

  1. we visit the site or get enough information from the client to understand the hazards
  2. we write site-specific RAMS covering the work, the hazards, the controls, the people involved and the emergency arrangements
  3. the director approves the RAMS
  4. we send the RAMS to the client and, where relevant, the airport operator, at least 5 working days before work starts, or earlier if they require it
  5. we do not start work until the client has accepted the RAMS
  6. we brief everyone on the job on the RAMS before work starts, and record that they have understood it.

If the work or the site changes, we stop and update the RAMS before carrying on.

Where our work counts as construction work under the Construction (Design and Management) Regulations 2015 (CDM 2015), for example installing fixed electrical, telecoms or computer equipment, we will meet our duties as a contractor or designer. This includes following the principal contractor's construction phase plan and providing information for the health and safety file.

4.3 Airport sites, security and inductions

Airports have strict safety and security rules. On airport sites we will:

  • complete the airport's site induction and any required security training before starting work
  • hold the correct airside pass, or be escorted at all times by an authorised escort where we do not have one
  • follow all security screening, restricted area and tool control rules
  • keep tools and materials under control at all times, and check for foreign object debris (FOD) when we finish, so nothing is left that could damage aircraft
  • wear high-visibility clothing and any other PPE the airport requires
  • follow the airport's rules on airside movement and never drive airside without the correct permit
  • plan work in public areas to keep passengers and staff away from hazards, using barriers and signs.

All client and site inductions follow the same principle: we complete them before work starts, and keep a record.

4.4 Permits to work

We will get every permit to work the client or site requires before starting the relevant task. This includes permits for electrical work, hot work, working at height and access to restricted areas. Before drilling or fixing into a building, we will ask for the site's asbestos information, as required by the Control of Asbestos Regulations 2012.

4.5 Working at height

We follow the Work at Height Regulations 2005:

  • we avoid working at height where we can, for example by assembling equipment at ground level
  • where we cannot avoid it, we use suitable equipment such as podium steps, mobile towers or mobile elevating work platforms (MEWPs), chosen in the RAMS
  • only people trained for the equipment may use it
  • we inspect access equipment before each use
  • we do not use ladders except for short, low-risk tasks where the RAMS shows they are suitable.

4.6 Electrical safety and safe isolation

We follow the Electricity at Work Regulations 1989:

  • we work on electrical equipment dead wherever possible
  • we use a safe isolation procedure: isolate, lock off, label, prove the tester, test dead, then prove the tester again
  • we never work live except where it is unreasonable to work dead and suitable precautions are in place, and only with the director's written approval and the client's permission
  • only competent people carry out electrical work. Fixed wiring and connections to building supplies are done by qualified electricians
  • our portable equipment is inspected and tested at suitable intervals.

4.7 Manual handling

We follow the Manual Handling Operations Regulations 1992. We avoid hazardous lifting where we can, use trolleys and lifting aids, and plan team lifts for heavy or awkward equipment. The RAMS covers any significant lifting.

4.8 Lone working

We avoid lone working on client sites. Where it cannot be avoided, the RAMS sets out the controls. These include agreed check-in times with the director, a working mobile phone and a clear escalation plan if someone does not check in. No one works alone on high-risk tasks such as electrical work or working at height.

4.9 Display screen equipment

Most of our work is at a computer. Under the Health and Safety (Display Screen Equipment) Regulations 1992, we will:

  • assess every workstation, including home workstations, when someone starts and when their setup changes
  • encourage regular breaks from screen work
  • pay for an eye test for anyone who regularly uses a screen, and for basic glasses if they are needed only for screen work.

4.10 Personal protective equipment (PPE)

We provide suitable PPE free of charge, as the Personal Protective Equipment at Work Regulations 1992 require. Typical PPE includes safety footwear, high-visibility clothing, hard hats, gloves and eye protection. The RAMS sets out the PPE needed for each job. PPE is the last line of defence, not a replacement for other controls.

4.11 Competent subcontractors

Before we use a subcontractor for site work, we check:

  • their qualifications and training for the work
  • their RAMS for their part of the work
  • their insurance
  • their health and safety record.

We brief subcontractors on our RAMS and the site rules, and we check that they follow them.

4.12 First aid

We follow the Health and Safety (First-Aid) Regulations 1981. On client sites we use the site's first aid arrangements, which we confirm during the induction and record in the RAMS. For our own work we keep a first aid kit and our director is the appointed person responsible for first aid arrangements.

4.13 Accidents and near misses

Everyone must report every accident, injury, near miss and dangerous occurrence to the director straight away, and to the client or site as their rules require.

  • We record every incident in our accident book.
  • The director investigates and records what will change to stop it happening again.
  • We report incidents to the Health and Safety Executive (HSE) where the Reporting of Injuries, Diseases and Dangerous Occurrences Regulations 2013 (RIDDOR) require it, within the required time limits. Where the incident happens on a client site, we agree with the client who will report it.

4.14 Training and records

We keep training records for everyone working for us, including site inductions, airport security training, access equipment training and electrical qualifications. We check that training is current before each job.

4.15 Consultation

We discuss health and safety with everyone in the company regularly, including at the start and end of every site job.

5. Monitoring and review

The director will:

  • check site work against the RAMS during the job
  • review all accidents and near misses
  • review this policy every year, and sooner after a serious incident, a change in the law or a significant change in our work.

Related policies: Equality, Diversity and Inclusion Policy, Whistleblowing Policy.

Organisation
Carefully Coded Ltd
Version
1.0
Owner
Tom Emmerson, Director
Effective from
19 November 2026
Next review
19 November 2027

Questions about this policy? Email info@carefully.codes.